The publisher is making a number of great observations about A Step-by-Step Guide to Installing a Bathtub as a whole in the article underneath.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough task. If the old tub is conveniently obtainable, the project can move rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is much better to consider using one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This article will aid you install a brand-new tub in your restroom if you have currently bought a brand-new tub as well as do not require to alter the setup of your previous water pipes.
Your devices and also material list must make up the following:
Getting ready for the Installation
Firstly, the sustaining frame provided with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to stop strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its final placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome due to the limited access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before moving on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, put the tub in the required setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the tub up until the level checks out degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints and brand-new pipework for leaks and tighten them if essential. Load the tub as well as additionally inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bath paneling as defined in the supplier's user's manual. Tiling and securing around the bathtub should wait until the bathtub has been utilized at the very least when as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Protect the faucet in position with the producer offered backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind must be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a stiff seal, creating the water to penetrate the wall in between the bath and the tiling, resulting in complications with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and installations. They are sold in tubes and cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealer can split relatively very early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader about Installing A Bathtub, I imagined sharing that excerpt was smart. Sharing is nice. You just don't know, you might be helping someone out. Thanks a lot for your time. Please come visit our blog back soon.
We've got answers!